Cyclekart Club of Australia Logo              
   
Forum
Build Pages
Groups
Photos
Videos
Events
Resources
Marketplace
Filter
Show results from selected filters below:
|
Suggested keywords
x
Loading cover... Drag cover to reposition
Pinky

Pinky

  Registered Users Last seen online, 3 months ago
Cyclekartiste
Timeline
About
Forum Posts
Build Pages
Groups
Albums
Videos
Events
More    
Introduction
Build Pages
View All
Pinned Items
Recent Activities
  •   Mick commented on this post about 10 months ago
    Pinky
    Pinky Pinky's Pocket Rocket
    · Edited Editing
    Started mocking up the suspension today. Yes, I know its upside down but I am just testing everything for sizing, width etc.

    I have these solid 50mmdia x 30mm discs for the front, they will get recessed into the end of the chassis for a nice round look, and will also support the end of the spring. I haven't cut the shape in yet as I don't want...
    Started mocking up the suspension today. Yes, I know its upside down but I am just testing everything for sizing, width etc.

    I have these solid 50mmdia x 30mm discs for the front, they will get recessed into the end of the chassis for a nice round look, and will also support the end of the spring. I haven't cut the shape in yet as I don't want to disturb the chassis until after I start welding.

    I made up these 50x10 SHS pieces for the end of the springs to slide in.
    More
    20240209_111857
    20240209_111909
    20240209_111903
    1
    0
    0
    0
    0
    0
    Mick reacted to this
    Comments (1)
    Post is under moderation
    Stream item published successfully. Item will now be visible on your stream.
  • Pinky
    Pinky Pinky's Pocket Rocket
    Editing
    Today I mocked up the engine and seat position.
    20240209_073558
    20240209_073549
    0
    0
    0
    0
    0
    0
    Comments (0)
    Post is under moderation
    Stream item published successfully. Item will now be visible on your stream.
  • Pinky
    Pinky Pinky's Pocket Rocket
    Editing
    I'm using a 75 x 25 section for the chassis. I have tapered the front. I haven't welded it yet as I may change my mind on the angle. Doing it all in stainless so for.
    20240208_171036
    0
    0
    0
    0
    0
    0
    Comments (0)
    Post is under moderation
    Stream item published successfully. Item will now be visible on your stream.
  •   Pinky's Pocket Rocket commented on this post about 3 months ago
    Pinky
    Pinky Pinky's Pocket Rocket
    Editing
    Cut up the frame and laid it out on the fabrication table. I'm happy with the dimensions.
    20240208_171023
    20240208_171030
    0
    0
    1
    0
    0
    0
    Mick reacted to this
    Comments (3)
    • Mick
      Mick
      I get a bit jealous of such awesome layout tables.
      10 months ago
      Reported
    • Andrew Stoker
      Andrew Stoker
      Pinky, Where did you score the plans from, looking into doing one of these for my daughter
      3 months ago
      Reported
    • Pinky
      Pinky
      Hi Andrew. I drew them up myself in aCad. Project is on hold at the moment due the economy and other financial priorities.
      3 months ago
      Reported
    Post is under moderation
    Stream item published successfully. Item will now be visible on your stream.
  • Pinky
    Pinky Pinky's Pocket Rocket
    Editing
    Started yesterday afternoon by test fitting the rear axle bits and bobs. A bit of machining and mucking about, but its now all there.
    20240208_171047
    0
    0
    0
    0
    0
    0
    Comments (0)
    Post is under moderation
    Stream item published successfully. Item will now be visible on your stream.
  •   Pinky reacted to this post about 10 months ago
    Pinky
    Pinky updated his profile picture
    Editing
    2
    0
    0
    0
    0
    0
    Mick and Pinky reacted to this
    Comments (0)
    Post is under moderation
    Stream item published successfully. Item will now be visible on your stream.
  • Pinky
    Pinky updated his profile
    Post is under moderation
    Stream item published successfully. Item will now be visible on your stream.
  • Pinky
    Pinky replied to a discussion, What does everyone think of these
    Editing
    A lot of the guys in France and UK use these wheels. I believe there may be a 4 stud hub from an ATV that will bolt up.
    1. View Post
    0
    0
    0
    0
    0
    0
    Post is under moderation
    Stream item published successfully. Item will now be visible on your stream.
  • Pinky
    Pinky just registered on the site
    Post is under moderation
    Stream item published successfully. Item will now be visible on your stream.
  • Pinky
    Pinky unlocked the badge Cyclekartiste
    Editing
    Cyclekartiste
    Cyclekartiste
    Being part of the Aussie Cyclekarts community. To unlock this badge, you need to register on this site.
    0
    0
    0
    0
    0
    0
    Comments (0)
    Post is under moderation
    Stream item published successfully. Item will now be visible on your stream.
There are no activities here yet
Unable to load tooltip content.

 

The Cyclekart Club of Australia acknowledges the Traditional Custodians of country and their connections to land, sea and community. 

We pay respect to Elders past and present and extend that respect to all Aboriginal and Torres Strait Islander peoples today.

 

The Cyclekart Club of Australia Incorporated